Question: How much air should I put in my FOX forks?

How much air should be in my Fox fork?

Sag range should be set to 15–20% of total fork travel. Make sure to set sag with the 3-position lever in the OPEN mode (see page 5). Do not exceed maximum air pressure: 34 FLOAT and Rhythm maximum air pressure is 120 psi.

How do you put air in a Fox fork?

1:002:20How to put air in a bike fork - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you use that as a guide and then you can go higher or lower if you like it firmer or less firm.MoreSo you use that as a guide and then you can go higher or lower if you like it firmer or less firm. And then thats really it you just take your pump pump up the jam pump it up.

What PSI should front fork be?

On the biggest stuff you hit, you should be close to bottoming or bottoming but not hard. If youre running into not using all the travel, drop the pressure in small 5psi decrements. If youre bottoming, raise pressure a bit. Suspension set-up is a process, not a single operation.

How do you set a SAG Fox?

2:022:57How To Set MTB Suspension Sag » ACADEMY | FOX - YouTubeYouTube

How much air should I put in my bike shocks?

For the rear shock, start at about half of your rider weight for air pressure. You will have to adjust from here, but you will want to achieve the proper SAG for your frame, as recommended by your frame manufacturer. Typically this is somewhere between 30-40% of overall travel.

How do I adjust the Fox Float DPS performance?

To achieve the best performance from your FOX suspension, adjust the air pressure to attain your proper sag setting. Sag is the amount your suspension compresses under your weight and riding gear. Sag range should be set to 25–30% of total shock travel. Your shock has a 4 digit ID code on the shock body.

How do I adjust my front fork suspension?

1:042:12Adjusting Your Front Suspension Fork | Rad Tech - YouTubeYouTube

How much air should I put in my air shocks?

The proper pressure of an air shock should be between 35 and 75 PSI. If it is any lower than this, the shocks will need to be filled with air.

How do you let the air out of a FOX 36?

Learn how to use the FOX High Pressure PumpRemove the blue air cap from the top of the left fork leg. Let the air out of the fork. Loosen the bottom nut 3-4 turns with a 10mm wrench. Compress the fork as much as possible. Pull the air-shaft assembly from the fork.

How many clicks is a rebound FOX 36?

FOX recommends beginning with the Open mode adjust set to 18 clicks out (counter-clockwise) from fully closed (clockwise). *Factory and Performance Elite Series forks only.

What PSI should my bike shock be?

Often yes, usually rear shocks run 100-200psi, but fork psi varies a lot, depending on the design. Get the sag around 25% (maybe slightly less sag in the front than the rear) and see how it rides (thats what really matters), adjust on the trail as needed.

What PSI should rear shocks be?

The Fox website says the safe operating range is 50 to 300 PSI.

How do you adjust air forks?

0:197:51Suspension fork settings - What they mean - YouTubeYouTube

What PSI is Fox DPX2?

3. Do not exceed maximum air pressure: FLOAT DPS and DPX2 air shocks have a maximum air pressure of 350 psi.

How many volume spacers does Fox 36 have?

FOX 36. 170mm travel: 0 spacers installed from factory. 5 spacers maximum. 160mm travel: 1 spacers installed from factory.

How do I adjust my Fox Float 36?

10:1820:18How To Set Up A Fox Suspension Mountain Bike Fork - YouTubeYouTube

Contact us

Find us at the office

Hurtarte- Aminov street no. 34, 93309 The Valley, Anguilla

Give us a ring

Oluwadamilola Gleich
+93 552 509 928
Mon - Fri, 8:00-17:00

Tell us about you